|
Are you looking for:
|
RTR-500 Wireless Base Station / Repeater
The RTR-500 can be used as either a “Base Unit” for our RTR-500 Wireless Data Logger Series or a “Repeater”
Easy-USB connection for performance as a Base Unit makes it perfect for on-site use. By registering the RTR-500 as a Base Unit, it is possible to Download Recorded Data and Current Readings from Remote Units and send the data by e-mail or FTP to a designated address. Moreover, by sending the recorded data to our online service "T&D WebStorage Service", it is possible to carry out Monitoring of Current Readings and/or Warnings as well as share the data via a PC web browser. Note: * RTR-500 can not be used with our RTR-50, RTR-5W and RTR-5 Series loggers.
|
TGPR-0704 Voltage Input 0 to 2.5/10/25V
Voltage input data logger that is housed in a robust, waterproof (IP68) rated case.
The TGPR-0704 can be used to record the output from a number of industry standard sensors.
Common applications include pressure and wind-speed monitoring.
FEATURES
- Reading Range 0 to 2.5/10/25V
- Robust Water-proof/Dust-proof Case
- 64,000 reading capacity
- Delayed start option
- 3 stop options
- 2 user-programmable alarms
- User-replaceable battery
- Free transfer function programming software
- USB or Serial download cables
YOU WILL ALSO NEED...
Software Tinytag Explorer, Windows software to configure, offload and analyse data from all Tinytags. The software is provided as a site licence and can be bundled with the appropriate download cable for your logger.
Connection
There are two cables available to download data from this logger. The preferred option, the CAB-0007-USB can connect to any of your computer's USB ports. If you have an older computer a CAB-0007 serial cable is also available.
Input Lead This Tinytag Voltage/XP Input Lead CAB-3239 is a five wire interface cable for Tinytag voltage and XP data loggers.
OPTIONAL SERVICES
Calibration Optional UKAS traceable calibration certificates for this single channel data logger can be purchased, for more details visit Tinytag calibration.
SEE RELATED PRODUCTS BELOW
|
WAS Force Washer Through Hole Load Cell
Micron WAS Force Washer Through Hole Load CellFeatures - Ranges 12.5kN to 540kN
- Stainless Steel Construction
- Environmentally sealed to IP66
- Special Sizes and ranges available
- Higher Accuracy versions available
- Many other variants may be available (please contact technical support with any requirements you may have)
The Micron WAS range of load cells from Micron Meters have been specifically designed for applications where there is a requirement for the force application component to pass through the center of the load cell. This style of product is often referred to by different names, including annular load cells, force washers, dough-nut load cells, through hole load cells etc.
The main application for the WAS series is measuring the tension in bolts for safety monitoring and control, or general quality control. Micron Meters specialize in the design of custom load cells, so have also been heavily involved in designing similar product for rock anchor force measurement, fork lift truck weighing, and tie rod tension monitoring.
If you have a requirement for an annular or through-hole load cell that can not be satisfied with the standard WAS series, then contact our technical department with your requirement, and we will probably be able to solve your application problem for you.
The WAS series can be supplied as a stand alone product or be incorporated into an instrumentation package, to meet your specific application requirements.
|
LVDT Signal Conditioner and Amplifier
LVDT Signal Conditioner and Amplifier (LVDT)Features - Sensor excitation of 4.5V RMS is provided
- Selectable excitation frequency between 1 and 5 kHz
- Selectable sensitivity from 20mV to 10V and fine trim with potentiometer
- Wide bandwidth (200 Hz) for test & measurement applications
- Selectable analogue output in voltage or current loop format including 4-20mA and 0-10VDC
- IP65 / NEMA4 ABS bulkhead mountable case with cable glands
The model LVDT or RVDT Amplifier / Signal Conditioner provides a convenient and flexible solution to the measurement of displacement or position (linear or angular) when using Linear Variable Differential Transformers or Rotary Variable Differential Transformers (LVDT's or RVDT's). |
DIA Stainless Steel Diaphragm Load Cell
Micron DIA Stainless Steel Diaphragm Load CellFeatures - Ranges 10 kg to 2000 kg
- Stainless steel construction
- Environmentally sealed to IP65 (IP67 can also be offered)
- Special sizes and ranges available
- Different mounting options available
- Integral connector versions available
The Micron series of Diaphragm Load Cells have been designed for use in a wide selection of different applications, particularly where there are low height constraints, for load cell installation.
The flexibility in the design of the DIA series enables the customer to virtually design the load cell to suit their installation exactly. Our engineers are on hand to assist you with this. Some of the standard variations that we offer include: male or female center threads, clear center holes etc.
The DIA series can be supplied as shown in this datasheet or can be modified to meet a particular application requirement. We are always pleased to discuss any special requirements that can be accommodated.
The DIA series can be supplied on it's own or combined with our extensive range of instrumentation to provide a complete load monitoring system.
|